必威官网登陆

?
您好,欢迎浏览艾瑞金属密封配件VCR接头官网! 收藏必威官网登陆 联系艾瑞
全国免费咨询热线: 13302860795
你当前的位置是:必威官网登陆>艾瑞动态>行业资讯> 卡套式管接头的安装-江门艾瑞精密机械经验分享

卡套式管接头的安装-江门艾瑞精密机械经验分享

来源:必威官网登陆 时间:2019-03-16 13:54:58 浏览次数: 85

[导读]: 卡套式管接头由三部分组成:接头体、卡套、螺母。当卡套和螺母套在钢管上插入接头体后,旋紧螺母时,卡套前端外侧与接头体锥面贴合,内刃均匀地咬入无缝钢管,形成有效密封。  The bayonet type pipe joint consists of three parts: the joint body, the bayonet and the nut. When the clamp sleeve and nut sleeve are

卡套式管接头由三部分组成:接头体、卡套、螺母。当卡套和螺母套在钢管上插入接头体后,旋紧螺母时,卡套前端外侧与接头体锥面贴合,内刃均匀地咬入无缝钢管,形成有效密封。

  The bayonet type pipe joint consists of three parts: the joint body, the bayonet and the nut. When the clamp sleeve and nut sleeve are inserted into the joint body on the steel pipe and the nut is tightened, the front and outside of the clamp sleeve are fitted with the taper surface of the joint body, and the inner edge evenly bites into the seamless steel pipe to form an effective seal.

111.jpg

  卡套接头的装配

  1、锯下合适长度的无缝钢管,去除端口毛刺。钢管端面要与轴线垂直,角度公差不大于0.5度。如果钢管需要折弯,则钢管端面至弯曲部位的直线段长度不能少于三倍螺母的长度。

  2、把螺母和卡套套在无缝钢管上。注意螺母和卡套的方向,不要装反了。

  3、在预装配接头体螺纹和卡套上涂上润滑油,把钢管插入接头体,(钢管一定要插到底)用手旋紧螺母。

  4、拧紧螺母直至卡套卡住钢管,这个转折点可以通过拧紧力矩的增加感受到(压力点)。

  5、达到压力点后,再将螺母拧紧1/2圈。

  6、将预装配接头体拆下,检查卡套刃边的嵌入情况,可见的突起带必须填满卡套前端的空间。卡套可以稍微旋转,但不能轴向移动。

  7、最终安装,将实际安装中的接头体的螺纹涂上润滑油、压紧螺母与之配合拧至可感觉到的拧紧力增加为止,接着再拧紧1/2圈安装完毕。

  Assembly of bayonet joint

  1. Saw off the seamless steel pipe of appropriate length to remove the burr of the end. The end surface of the steel tube shall be perpendicular to the axis, and the Angle tolerance shall not be greater than 0.5 degree. If the steel pipe needs to be bent, the straight segment length from the end face of the steel pipe to the bending part shall not be less than three times the length of the nut.

  2. Put the nut and clip sleeve on the seamless steel pipe. Pay attention to the direction of the nut and clamp, do not install the reverse.

  3. Lubricate the thread and clamp sleeve of the preassembled joint body, insert the steel pipe into the joint body, (the steel pipe must be inserted to the end) tighten the nut by hand.

  4. Tighten the nut until the steel pipe is stuck by the clamp sleeve. This turning point can be felt (pressure point) by increasing the tightening torque.

  5. After reaching the pressure point, tighten the nut 1/2 turn.

  6. Remove the preassembled connector body, check the insertion of the edge of the card sleeve, and the visible protrusion belt must fill the space of the front end of the card sleeve. The sleeve can be rotated slightly but does not move axially.

  7. For final installation, the thread of the joint body in actual installation shall be lubricated and the compression nut shall be screwed together until the perceived tightening force is increased, and then the installation shall be completed by tightening 1/2 circle.

222.jpg

文章出自江门艾瑞 转载请标明出处

VCR接头订购联系:秦先生 17688183787


免责声明:部分文章信息来源于网络以及网友投稿,本网站只负责对文章进行整理、排版、编辑,是出于传递 更多信息之目的,并不意味着赞同其观点或证实其内容的真实性,如必威官网登陆文章和转稿涉及版权等问题,请作者在及时联系必威官网登陆,我们会尽快处理。
标题:卡套式管接头的安装-江门艾瑞精密机械经验分享 地址:/content/143.html
来说两句
 昵称:
* 验证码:
?
用户评论
来自北京的客户
2019-03-19 15:11:24

江门艾瑞vcr接头生产厂家生产的vcr接头产品质量真的很好,已经合作过2年了。

来自四川的客户
2019-05-09 15:26:07

跟很多家vcr接头贸易商合作过,但是自从跟艾瑞vcr接头生产厂家合作过就一直觉得比其他贸易商好,可以看到产品的质量差别。

为自东北的客户
2019-01-19 15:20:06

公司需要316不锈钢材质的vcr接头,刚好遇到了艾瑞精密机械科技有限公司,其能够生产316材质的vcr接头,满足了公司的需求。

来自广东的客户
2019-03-19 08:40:24

vcr接头的厂家在国内真的很少,一直合作的就是艾瑞精密机械科技有限公司了,公司生产的产品符合我司的要求。

NEW & CASE 新闻中心

必威官网登陆

?
XML 地图 | Sitemap 地图